Wellhead Penetrators - Vertical Single Mandrel with 45 and 90 degree Surface Connector options.

Wellhead Penetrators - the Side-Entry Feedthru System is the perfect solution when the lower wellhead penetrator is unable to exit the wellhead vertically.

Wellhead Penetrators - Split-Phase or ‘3-Leg’ Feedthru Systems deliver the same power in a more space efficient configuration.

ESP Sensors - Advanced Motor Temperature Monitoring and 3-Axis Vibration Measurement, available in High Temperature and High Accuracy models.

ESP Gauges / Sensors - Advanced Motor Temperature Monitoring, 3-Axis Vibration Measurement and Pump Discharge Pressure available in High Temperature and High Accuracy models.

The Y-Tool system offsets the ESP in the well to provide a straight line conduit for wireline or coiled tubing tools to bypass the ESP. Dual Systems allows the operator to run two complete ESP systems in one well, providing a downhole back-up system.

ESP Twin CAN (POD) - by configuring one CAN above the other, two complete ESP systems can be deployed in one well to provide a downhole backup system.

A dual system using two independent ESPs that separately and individually produce from two production zones in the same well without mingling the fluids.

A dual ESP system that enables maximum production in high volume/high PI wells by providing high downhole horsepower shared between two standard-range ESPs.

The Y-Chek is firmly established as the New Standard in automatic Y-Tool technology. This automatic downhole valve is located within the RMSpumptools Y-Tool and is designed to prevent recirculation of pumped fluid from an operated ESP.

Bypass Plugs including Blanking Plugs, Coiled Tubing Logging Plugs, Wireline Logging Plugs and Isolation Sleeves - a full range of complimentary ESP Bypass products to facilitate intervention and maximise production.

RMSpumptools world renowned Y-Tool (ESP Bypass System) represents design at its functional best, providing a means of allowing well intervention below an ESP using wireline or coiled tubing.

The patented RMSpumptools ADV® (Automatic Diverter Valve) is a field proven, fully automatic valve that controls tubing to annulus communication.

The NRV is a high specification precision engineered piston-type check valve for use in specialist downhole applications.

The Adjustable Union is a tubing string mechanical telescopic device designed to adjust the spacing within the tubing string where close tolerancing and accuracy is required.

The PRL (positive rotational lock) Swivel Sub is an in-line tubing device designed to provide orientation between two sets of tubing assemblies.

The BOP CAN provides a pressure barrier around the production tubing, power cable and control lines to allow BOP RAMS to close off during well testing with an ESP.

The Pump Chek is an all metal pressure sealing valve designed to provide a pressure barrier to isolate ESPs preventing fall-back on the pump on ESP shutdown - a known cause of ESP failure.

RMSpumptools SandCat is a down-hole centrifugal Sand Separator designed to separate out sand from the produced fluid before it enters the pump.

The ESP Motor Shroud is a cylindrical shroud which covers the motor length of the ESP. It is hung off a special clamp at the pump intake neck and is packed off against the body of the pump section to prevent fluid from entering from above.

The STEALTH Clamp™ has been developed to give maximum protection to control lines and power cables in a low profile, slimline design. The patented threaded clamping design prevents slippage when running in hole and can withstand 40,000lbs of axial load before moving.

No Tapes, No Epoxy, No Gel and Less Than 10 Minutes Assembly Time in the Field after the Cable is Stripped.

No Tapes, No Epoxy, No Gel and Minimal Assembly Time in the Field after the Cable is Stripped.

ALTERN8 provides the interface to produce or de-water wells using alternatively deployed ESP’s without pulling the existing completion or making facilities modifications - saving significant cost.

The RMSpumptools CAN Hanger provides a beneficial alternative to running retrievable packers where a second barrier for produced fluids is required.

ESP Bypass Neck Clamps in all sizes and fully adjustable to fit any brand of ESP, ensuring maximum protection of Control Lines and Cable.